MMC castings, MMC Hammer, MMC blow bar, MMC Jaw plate,MMC cone, High Mn Steel ceramic composite, High Cr ceramic composite, Martensite steel ceramic composite
Location: Home > Product > Ceramic insert castings > MMC Jaw plate - Ceramic insert Jaw plate
-
-
MMC Jaw plate - Ceramic insert Jaw plate
We have mature and advanced MMC casting technology and We can produce all kinds of wear-resisting parts of crusher by MMC casting technology. The spare parts by ceramic compound casting is high wear resistant, the life span is several times of the traditional material. Our product include: MMC-Mn - High Mn Steel matrix ceramic composite Jaw plate, Hammer, Mantle/Cone, Blow bar, Liner for Ballmill, Liner of AG/SAG. MMC-Cr - High Cr cast iron matrix Ceramic composite blow bar, Liner, Hammer, Downspout, Grinding roller and liner of vertical mill, Impeller, Liner and hammer of VSI. MMC-M - Martensite Steel matrix Ceramic composite Liner, Blow bar, Hammer, Liner of Downspout, weldability wear-resistant plate. If you are interested in MCC Wear Resistant Spare Part, please do not hesitate to contact us immediately. I will supply best competitive price! and product of high quality!
Detail:
DJM 陶瓷复合鄂式碎机备件（齿板）技术介绍
DJM ceramic composite jaw crusher spare parts (jaw plate) technology introduction
颚式破碎机的工作部分是两块颚板，一是固定颚板（定颚），垂直（或上端略外倾）固定在机体前壁上，另一是活动颚板（动颚），位置倾斜，与固定颚板形成上大下小的破碎腔（工作腔）。活动颚板对着固定颚板做周期性的往复运动，时而分开，时而靠近。分开时，物料进入破碎腔，成品从下部卸出；靠近时，使装在两块颚板之间的物料受到挤压，弯折和劈裂作用而破碎。颚式破碎机目前广泛使用的齿板多是采用高锰钢制造。由于物料的冲刷，破碎过程中的挤压，碾磨作用，造成齿板磨损严重，针对这一情况，DJM 选用高锰钢为基材的陶瓷复合材料，即齿板的基体采用高锰钢，同时在基体上嵌铸具有高耐磨性的陶瓷随形加强筋，在保持高锰钢原有的加工硬化耐冲击性能的同时提高了高锰钢的耐磨强度，陶瓷复合材料齿板的寿命约为高锰钢齿板的2倍以上。
Work part of the jaw crusher is two pieces of jaw plate, one is the fixed jaw plate (
fixed
jaw),
which is
vertical (or the upper slightly extraversion) fixed in front of the body wall, the other is movable jaw
plate
(
movable
jaw),
which is
tilt, form
big end dowm
crushing cavity (work
cavity
).
movable
jaw
plate press the fixed jaw plate with
periodic reciprocating motion, sometimes separately, sometimes near. Separately, material into the crushing cavity, finished products discharge
from the lower ; Approached, the materials are squeezed between two pieces of jaw plate, bending and fracturing effect
to
broken. Jaw crusher is widely used high manganese steel manufactur
ing
. Due to the material erosion, the
extrusion
process broken
,
grinding effect, cause plate wear serious, in order to solve this situation, DJM chooses high manganese steel as base material of the ceramic composite materials,
which is
plate
basement with
high
manganese steel
and then
embed
the high wear resistance With stiffener into the basement.below
keep
ing
original work hardening of high manganese steel impact resistance performance
and
improv
ing
wear resistance strength at the same time, the life of the ceramic composite plate is about 2 times
longer
than the high manganese steel
basement
plate.
Product include: Mn18Cr2+Ti-Re Mn18Cr2 Mn13 Mn13Cr2 Martensite steel
Pre Item:None
Next Item:None
Next Item:None
Product
Contact:
Tel: +86-10-8890 9291
MP: +86-13901376361
WhatsApp: +86-13901376361
Email: info@djm-bj.com leegang@djm-bj.com
Web: www.djm-bj.com
- BEIJING JINMEI ENTREPRENEUR CO .,LTD
- Tel: +86-10-8890 9291 MP: +86-13901376361 WhatsApp: +86-13901376361 Email: info@djm-bj.com leegang@djm-bj.com
- Room No.1403 TaiRan Building, No.36 GuSheng Road, ShiJingShan District, Beijing, China.100043
- Copyright 2006-2018 DJM All Right Reservered. Report To Improve Product
京ICP备11022145号-2 - MMC Mill part, MMC Impact bar, MMC Mantle, MMC Crusher part, Ceramic composite High Mn Steel, ceramic particules composite casting,ceramic Insert composite castings
Powered by
MetInfo
3.0 ©2008-2024
www.MetInfo.cn